-
ISO 10817-1 1998 Rotating shaft vibration measuring systems — Part 1 Relative and absolute sensing of radial vibration.pdf
-
ISO 10841 1996 Aircraft — Catering vehicle for large capacity aircraft — Functional requirements.pdf
-
ISO 10843 1997 Acoustics — Methods for the description and physical measurement of single impulses or series of impulses.pdf
-
ISO 10847 1997 Acoustics — In-situ determination of insertion loss of outdoor noise barriers of all types.pdf
-
ISO 10887 1999 Key type three-jaw drill chucks — Specification.pdf
-
ISO 10888 1999 Keyless type three-jaw drill chucks — Specification.pdf
-
ISO 10889-8 1997 Tool holders with cylindrical shank — Part 8 Type Z, accessories.pdf
-
ISO 10899 1996 High-speed steel two-flute twist drills — Technical specifications.pdf
-
ISO 10914 1996 Assembly tools for screws and nuts — Sockets and wrenches for spline drive.pdf
-
ISO 10958-1 1998 Snowboards — Binding mounting area — Part 1 Requirements and test methods for snowboards without inserts.pdf
-
ISO 10972-1 1998 Cranes — Requirements for mechanisms — Part 1 General.pdf
-
ISO 10990-4 1999 Animal (mammal) traps — Part 4 Methods for testing killing-trap systems used on land or underwater.pdf
-
ISO 10990-5 1999 Animal (mammal) traps — Part 5 Methods for testing restraining traps.pdf
-
ISO 11019 1998 Oil of roots of lovage (Levisticum officinale Koch).pdf
-
ISO 11020 1998 Oil of turpentine, Iberian type (Pinus pinaster Sol.).pdf
-
ISO 11021 1999 Essential oils — Determination of water content — Karl Fischer method.pdf
-
ISO 11024-1 1998 Essential oils — General guidance on chromatographic profiles — Part 1 Preparation of chromatographic profiles for presentation in standards.pdf
-
ISO 11024-2 1998 Essential oils — General guidance on chromatographic profiles — Part 2 Utilization of chromatographic profiles of samples of essential oils.pdf
-
ISO 11041 1996 Workplace air — Determination of particulate arsenic and arsenic compounds and arsenic trioxide vapour — Method by hydride generation and atomic absorption spectrometry.pdf
-
ISO 11042-1 1996 Gas turbines — Exhaust gas emission — Part 1 Measurement and evaluation.pdf
-
ISO 11042-2 1996 Gas turbines — Exhaust gas emission — Part 2 Automated emission monitoring.pdf
-
ISO 11043 1998 Oil of basil, methyl chavicol type (Ocimum basilicum L.).pdf
-
ISO 11055 1996 Flywheels for reciprocating internal combustion engines — Installation dimensions for clutches.pdf
-
ISO 11064-3 1999 Ergonomic design of control centres — Part 3 Control room layout.pdf
-
ISO 11086 1996 Gas turbines — Vocabulary.pdf
-
ISO 11102-2 1997 Reciprocating internal combustion engines — Handle starting equipment — Part 2 Method of testing the angle of disengagement.pdf
-
ISO 11106-1 1997 Photography — Slide trays for projectors — Part 1 Straight slide tray, open type (European design).pdf
-
ISO 11108 1996 Information and documentation — Archival paper — Requirements for permanence and durability.pdf
-
ISO 11126-9 1999 Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 9 Staurolite.pdf
-
ISO 11212-1 1997 Starch and derived products — Heavy metals content — Part 1 Determination of arsenic content by atomic absorption spectrometry.pdf
-
ISO 11212-2 1997 Starch and derived products — Heavy metals content — Part 2 Determination of mercury content by atomic absorption spectrometry.pdf
-
ISO 11212-3 1997 Starch and derived products — Heavy metals content — Part 3 Determination of lead content by atomic absorption spectrometry with electrothermal atomization.pdf
-
ISO 11212-4 1997 Starch and derived products — Heavy metals content — Part 4 Determination of cadmium content by atomic absorption spectrometry with electrothermal atomization.pdf
-
ISO 11214 1996 Modified starch — Determination of carboxyl group content of oxidized starc.pdf
-
ISO 11215 1998 Modified starch — Determination of adipic acid content of acetylated di-starch adipates — Gas chromatographic method.pdf
-
ISO 11216 1998 Modified starch — Determination of content of carboxymethyl groups in carboxymethyl starch.pdf
-
ISO 1122-1 1998 Vocabulary of gear terms — Part 1 Definitions related to geometry.pdf
-
ISO 1122-2 1999 Vocabulary of gear terms — Part 2 Definitions related to worm gear geometry.pdf
-
ISO 11242 1996 Aircraft — Pressure equalization requirements for cargo containers.pdf
-
ISO 11306 1998 Corrosion of metals and alloys — Guidelines for exposing and evaluating metals and alloys in surface sea water.pdf
-
ISO 11315-1 1997 Photography — Projection in indoor rooms — Part 1 Screen illumination test for still projectors.pdf
-
ISO 11315-2 1997 Photography — Projection in indoor rooms — Part 2 Screen luminance test f.pdf
-
ISO 11334-4 1999 Walking aids manipulated by one arm — Requirements and test methods — Part 4 Walking sticks with three or more legs.pdf
-
ISO 11369 1997 Water quality — Determination of selected plant treatment agents — Method using high performance liquid chromatography with UV detection after.pdf
-
ISO 11375 1998 Building construction machinery and equipment — Terms and definitions.pdf
-
ISO 11377 1997 Textile floor coverings — Floor soiling — Test site set-up and soiling evaluati.pdf
-
ISO 11408 1999 Chemical conversion coatings — Black oxide coating on iron and steel — Specification and test methods.pdf
-
ISO 11415 1997 Tools for pressing — Die sets.pdf
-
ISO 11421 1997 Optics and optical instruments — Accuracy of optical transfer function (OTF) measurement.pdf
-
ISO 11423-1 1997 Water quality — Determination of benzene and some derivatives — Part 1 Head-space gas chromatographic method.pdf
-
ISO 11423-2 1997 Water quality — Determination of benzene and some derivatives — Part 2 Method using extraction and gas chromatography.pdf
-
ISO 11428 1996 Ergonomics — Visual danger signals — General requirements, design and te.pdf
-
ISO 11429 1996 Ergonomics — System of auditory and visual danger and information signals.pdf
-
ISO 11450 1999 Equipment for harvesting and conservation — Round balers — Terminology and commercial specifications.pdf
-
ISO 11468 1997 Plastics — Preparation of PVC pastes for test purposes — Dissolver method.pdf
-
ISO 11497 1998 Telemark skis and bindings — Binding mounting area — Requirements and test methods.pdf
-
ISO 1150 1997 Textile machinery and accessories — Drop wires for warp stop motions for weaving machines with automatic drawing-in.pdf
-
ISO 11520-1 1997 Agricultural grain driers — Determination of drying performance — Part 1 General.pdf
-
ISO 11541 1997 Natural gas — Determination of water content at high pressure.pdf
-
ISO 11561 1999 Ageing of thermal insulation materials — Determination of the long-term change in thermal resistance of closed-cell plastics (accelerated laboratory test methods).pdf
-
ISO 1158 1998 Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content.pdf
-
ISO 11599 1997 Determination of gas porosity and gas permeability of hydraulic binders containing embedded radioactive waste.pdf
-
ISO 11614 1999 Reciprocating internal combustion compression-ignition engines — Apparatus for measurement of the opacity and for determination of the light absorption coefficient of exhaust gas.pdf
-
ISO 11621 1997 Gas cylinders — Procedures for change of gas service.pdf
-
ISO 11630 1997 Cranes — Measurement of wheel alignment.pdf
-
ISO 11631 1998 Measurement of fluid flow — Methods of specifying flowmeter performance.pdf
-
ISO 11632 1998 Stationary source emissions — Determination of mass concentration of sulfur dioxide — Ion chromatography method.pdf
-
ISO 11634 1996 Snowboard-boots — Interface with snowboard bindings.pdf
-
ISO 11650 1999 Performance of refrigerant recovery and or recycling equipment.pdf
-
ISO 11652 1997 Steel and iron — Determination of cobalt content — Flame atomic absorption spectrometric method.pdf
-
ISO 11653 1997 Steel — Determination of high cobalt content — Potentiometric titration method after separation by ion exchange.pdf
-
ISO 11654 1997 Acoustics — Sound absorbers for use in buildings — Rating of sound absorpt.pdf
-
ISO 11667 1997 Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods.pdf
-
ISO 11678 1996 Agricultural irrigation equipment — Aluminium irrigation tubes.pdf
-
ISO 11683 1997 Packaging — Tactile warnings of danger — Requirements.pdf
-
ISO 11689 1996 Acoustics — Procedure for the comparison of noise-emission data for machinery and equipment.pdf
-
ISO 11727 1999 Pneumatic fluid power — Identification of ports and control mechanisms of control valves and other components.pdf
-
ISO 1174-2 1996 Assembly tools for screws and nuts — Driving squares — Part 2 Driving squares for power socket tools.pdf
-
ISO 11759 1999 Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) — Specification.pdf
-
ISO 11782-1 1998 Corrosion of metals and alloys — Corrosion fatigue testing — Part 1 Cycles to failure testing.pdf
-
ISO 11782-2 1998 Corrosion of metals and alloys — Corrosion fatigue testing — Part 2 Crack propagation testing using precracked specimens.pdf
-
ISO 11784 1996 Radio frequency identification of animals — Code structure.pdf
-
ISO 11785 1996 Radio frequency identification of animals — Technical concept.pdf
-
ISO 11789 1999 Powered edgers with rigid cutting means — Definitions, safety requirements and test procedures.pdf
-
ISO 11800 1998 Information and documentation — Requirements for binding materials and methods used in the manufacture of books.pdf
-
ISO 11820 1996 Acoustics — Measurements on silencers in situ.pdf
-
ISO 11821 1997 Acoustics — Measurement of the in situ sound attenuation of a removable.pdf
-
ISO 11822 1996 Information and documentation — Extension of the Arabic alphabet coded character set for bibliographic information interchange.pdf
-
ISO 1183-3 1999 Plastics — Methods for determining the density of non-cellular plastics — Part 3 Gas pyknometer method.pdf
-
ISO 11838 1997 Motorcycle and motorcycle-rider kinematics — Vocabulary.pdf
-
ISO 11841-1 2000 Road vehicles and internal combustion engines — Filter vocabulary — Part 1 Definitions of filters and filter components.pdf
-
ISO 11841-2 2000 Road vehicles and internal combustion engines — Filter vocabulary — Part 2 Definitions of characteristics of filters and their components.pdf
-
ISO 11843-1 1997 Capability of detection — Part 1 Terms and definitions.pdf
-
ISO 11857 1999 Textile floor coverings — Determination of resistance to delamination.pdf
-
ISO 11859 1999 Textile floor coverings — Pure wool, hand-knotted pile carpets — Specificati.pdf
-
ISO 11860 1999 Textile floor coverings — Jute carpet backing fabric — Specification.pdf
-
ISO 11861 1999 Textile floor coverings — Coir mats — Types and specification.pdf
-
ISO 11881 1999 Corrosion of metals and alloys — Exfoliation corrosion testing of aluminium.pdf
-
ISO 11883 1997 Optics and optical instruments — Microscopes — Marking of stereomicrosco.pdf
-
ISO 11905-1 1997 Water quality — Determination of nitrogen — Part 1 Method using oxidative digestion with peroxodisulfate.pdf
-
ISO 11907-4 1998 Plastics — Smoke generation — Determination of the corrosivity of fire effluents — Part 4 Dynamic decomposition method using a conical radiant heater.pdf
-
ISO 11922-2 1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 2 Inch-based series.pdf
-
ISO 11923 1997 Water quality — Determination of suspended solids by filtration through glass-fibre filters.pdf
-
ISO 11925-3 1997 Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3 Multi-source test.pdf
-
ISO 11928-2 2000 Micrographics — Quality control of graphic COM recorders — Part 2 Quality criteria and control.pdf
-
ISO 11932 1996 Activity measurements of solid materials considered for recycling, re-use or disposal as non-radioactive waste.pdf
-
ISO 11933-1 1997 Components for containment enclosures — Part 1 Glove bag ports, bungs for glove bag ports, enclosure rings and interchangeable.pdf
-
ISO 11933-2 1997 Components for containment enclosures — Part 2 Gloves, welded bags, gaiters for remote - handling tongs and for manipulators.pdf
-
ISO 11933-3 1998 Components for containment enclosures — Part 3 Transfer systems such as plain doors, airlock chambers, double door transfer systems, leaktight connections for waste drums.pdf
-
ISO 11940 1998 Information and documentation — Transliteration of Thai.pdf
-
ISO 11948-1 1996 Urine-absorbing aids — Part 1 Whole-product testing.pdf
-
ISO 11957 1996 Acoustics — Determination of sound insulation performance of cabins — Laboratory and in situ measurements.pdf
-
ISO 11995 1996 Aircraft — Stability requirements for loading and servicing equipment.pdf
-
ISO 12001 1996 Acoustics — Noise emitted by machinery and equipment — Rules for the drafting and presentation of a noise test code.pdf
-
ISO 12020 1997 Water quality — Determination of aluminium — Atomic absorption spectrometric methods.pdf
-
ISO 1203 1998 Photography — Roll film cameras — Back window location.pdf
-
ISO 12040 1997 Graphic technology — Prints and printing inks — Assessment of light fastness using filtered xenon arc light.pdf
站内资源均来自网友分享或网络收集整理，若无意中侵犯到您的权利，敬请联系我们
微信(点击查看客服)，我们将及时删除相关资源。
