ISO/TS TECHNICAL SPECIFICATION 19159-1 First edition 2014-07-15 Geographic information Calibration and validation of remote sensing imagery sensors and data - Part 1: Optical sensors Information géographique - Calibration et validation de capteurs de teledétecion Partie 1: Capteurs optiques Reference number IS0/TS19159-1:2014(E) ISO @ IS0 2014 ted without license from IHS Not for Resale IS0/TS 19159-1:2014(E) COPYRIGHTPROTECTEDDOCUMENT @ISO2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ IS0 2014 - All rights reserved No reproduction or networking permited without license from IHS Not for Resale IS0/TS 19159-1:2014(E) Contents Page Foreword ..iv Introduction. ..V 1 Scope. ..1 2 Conformance 3 Normative references 4 Terms and definitions ..1 5 Abbreviated terms and symbols .8 5.1 Abbreviated terms .8 5.2 Symbols. 10 5.3 Variable names of the Jacobsen model 10 5.4 Conventions 10 6 Calibration .11 6.1 Project 11 6.2 Package OpticsSensor, Geometry 16 6.3 Package OpticsSensor, Radiometry 25 6.4 Package OpticsCalibrationFacility, Geometry 35 6.5 Package OpticsCalibrationFacility, Radiometry .41 6.6 Package OpticsValidation .45 7 Documentation .46 7.1 Semantics. .46 7.2 Package Documentation ..47 Annex A (normative) Abstract test suite ..49 Annex B (normative) Data dictionary ..54 Annex C (normative) Self calibration models ..85 Annex D (informative) Calibration and validation quality measures ..94 Bibliography. .100 ii ithout license from IHS Not for Resale IS0/TS 19159-1:2014(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out throughIsotechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the IsO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of Iso documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. Details of anypatentrightsidentifiedduringthedevelopmentofthedocumentwillbeintheIntroductionand/or on the Iso list of patent declarations received. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of IsO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISo/TC 211, Geographic information/Geomatics. Iso 19159 consists of the following parts, under the general title Geographic information - Calibration and validation o