ISO/TS TECHNICAL SPECIFICATION 13399-3 Third edition 2021-11 Cutting tool data representation and exchange - Part 3: Reference dictionary for tool items Reference number IS0/TS13399-3:2021(E) ISO @ISO2021 IS0/TS13399-3:2021(E) COPYRIGHTPROTECTEDDOCUMENT @IS02021 All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in anyform or by anymeans, electronic or mechanical, including photocopying, orposting on theinternetoran intranet,withoutpriorwrittenpermission.Permissioncanberequestedfrom eitherIsoattheaddressbelow or ISO's member body in the country of the requester. ISO copyright office CP401 : Ch.de Blandonnet 8 CH-1214 Vernier,Geneva Phone: +4122 749 0111 Email: [email protected] Website:www.iso.org Published in Switzerland ii @IS0 2021-All rights reserved IS0/TS13399-3:2021(E) Contents Page Foreword ..iv Introduction ..V 1 Scope. .1 2 Normative references 3 Terms and definitions. .2 4 Abbreviatedterms .4 5 Representationoftheontologyconceptsasdictionaryentries .5 5.1 General. .5 5.2 Referencesystemsfortoolitems 5 5.2.1 General .5 5.2.2 cutting_reference_point 6 5.2.3 feed_direction_primary 6 5.2.4 master_insert 6 5.2.5 prismatic_tool_item_position 7 5.2.6 round_tool_item_position .7 5.2.7 tool_cutting_edge_plane. 7 5.2.8 tool_feed_plane. .7 5.2.9 tool_rake_plane 7 5.3 Tool item feature.. .8 5.3.1 tool_item_feature .8 5.3.2 chip_management. .8 5.3.3 drill_point 8 5.3.4 guide_pilot_feature 8 5.3.5 pilot_drill_feature 8 5.3.6 tool_hub .8 5.4 Tool item type. 8 5.4.1 tool_item_type 8 5.4.2 broach 9 5.4.3 burr_tool 9 5.4.4 cartridge 9 5.4.5 drill .10 5.4.6 mill. 11 5.4.7 ream. .12 5.4.8 rotating_borer .13 5.4.9 threading_die .13 5.4.10 threading_tap. .13 5.4.11 turn. .14 5.5 Generalfeaturetypes .. 14 5.6 Cutting item feature. .15 5.7 Connectionitemfeature ..15 6 Propertiesfortoolitemfeaturesandtoolitemtypes ..15 AnnexA (normative) Principles of the IS013399 series .23 AnnexB(informative)Classificationtable .26 AnnexC(informative)Classdefinitions .30 AnnexD (informative) Tool itemproperty definitions .90 AnnexE (informative) Illustrations ofproperties .339 AnnexF(informative)ISYCpictures. .345 Bibliography 460 IS0 2021-All rights reserved iii IS0/TS13399-3:2021(E) Foreword Iso (the International Organization for Standardization) is a worldwidefederation ofnational standards bodies (IsO member bodies).The work of preparing International Standards is normally carried out throughIsotechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work. IsOcollaboratescloselywiththeInternationalElectrotechnicalCommission(IEC)onallmattersof electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are describedintheIso/IEcDirectives,Part1.Inparticular,thedifferentapprovalcriterianeededforthe different types of IsO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (seewww.iso.org/directives). Attention is drawn to thepossibility that some of theelements of this document maybe the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the Iso list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation of the voluntary nature of standards, the meaning of Iso specific terms and expressions related to conformity assessment,as well as information about Iso's adherence to the World Trad