BS IS0 18758-2:2018 BSl Standards Publication Imperial College London, Version corre Mining and earth-moving machinery Rock drill rigs and rock reinforcement rigs Part 2: Safety requirements bsi. BS IS0 18758-2:2018 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 18758-2:2018 The UK participation in its preparation was entrusted to Technical A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2018 Published by BSI Standards Limited 2018 ISBN 978 0 580 94166 5 ICS 53.100; 73.100.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018. Amendments/corrigenda issued since publication Date Text affected BS ISO 18758-2:2018 INTERNATIONAL ISO STANDARD 18758-2 First edition 2018-06 Mining and earth-moving machinery - Rock drill rigs and rock reinforcement rigs - Part 2: Safety requirements Engins d'exploitation miniere et de terrassement - Appareils de forage et de renfort de roches - Partie 2: Exigences de sécurité Reference number ISO 18758-2:2018(E) Tso @IS02018 BS ISO 18758-2:2018 IS0 18758-2:2018(E) , Imperial College London, Version correct as of 06/06/2018 Licensed copy: Imperial College , COPYRIGHT PROTECTED DOCUMENT @I IS02018 All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either IsO at the address below or Iso's member body in the country of the requester. ISO copyright office CP 401 : Ch. de Blandonnet 8 CH-1214 Vernier, Geneva Phone: +41 22 749 01 11 Fax: +41 22 749 09 47 Email: [email protected] Website: www.iso.org Published in Switzerland ii @ IS0 2018 - All rights reserved BS IS0 18758-2:2018 IS0 18758-2:2018(E) Contents Page Foreword ..vi Introduction. ..vii 1 Scope. 2 Normative references .... 3 Terms and definitions ..4 4 Safety requirements 4.1 General requirements .4 4.1.1 General. ..4 4.1.2 Ergonomics. ..5 4.1.3 Hot and cold surfaces and sharp edges. ..5 4.1.4 Hoses, pipes and fittings under pressure 5 4.1.5 Handling of the rig and its parts. 4.1.6 Access to operating positions and servicing points .5 4.1.7 Isolation of external electrical energy sources ..6 4.1.8 Prevention of unexpected start-up .6 4.2 Driving, tramming and operating position .6 4.2.1 General .6 4.2.2 Operator's position. .6 4.2.3 Visibility.. 4.2.4 Operator protective structures. .9 4.3 Controls, functions and systems 10 4.3.1 General. .10 4.3.2 Starting. .10 4.3.3 Stopping - Normal stopping ..10 4.3.4 Failure of the power supply ..10 4.4 Control devices .10 4.4.1 General .10 4.4.2 Control system of remote controlled and automated rigs 4.4.3 Emergency stop and safety devices. .11 4.4.4 Operating instrumentation. .12 4.5 Stability. .12 4.6 Steering .12 4.7 Carrier brakes ..12 4.7.1 General. ..12 4.7.2 General requirements for wheel-mounted rigs. ..12 4.7.3 Service braking system for wheel-mounted rigs .13 4.7.4 Secondary braking system for wheel-mounted rigs ..13 4.7.5 Parking braking system for wheel-mounted rigs ..13 4.7.6 Braking systems for crawler-mounted rigs. 4.7.7 Braking systems for "skid steer" wheel-mounted rigs. 4.8 Tyres and rims. ..13 4.9 Protection against moving parts ..14 4.9.1 General. ..14 4.9.2 Moving parts involved in the working process. ..14 4.10 Electrical installations.. ..15 4.10.1 Electric power installation .15 4.10.2 Electromagnetic compatibility (EMC) .15 4.10.3 Battery installation.. ..16 4.11 Machines po