ISO INTERNATIONAL STANDARD 13628-11 First edition 2007-09-15 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications Industries du pétrole et du gaz naturel Conception et exploitation des systemes de production immergés- Partie 11: Systemes de canalisations flexibles pour applications sous- marines et en milieu marin Reference number ISO 13628-11:2007(E) @ ISO 2007 THS unde ISO 13628-11:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT @ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2007 - All rights reserved without license from IHS Not for Resale ISO 13628-11:2007(E) Contents Page Foreword. Introduction vi 1 Scope 2 Normative references. 3 Terms, abbreviated terms, definitions and symbols.. 3.1 Terms and definitions... 3.2 Symbols and abbreviated terms . 4 System, pipe, and component description .. 4.1 Introduction........... 4.2 Flexible pipe systems... 8 4.3 Flexible pipe description... 15 4.4 24 5 Pipe design considerations .. .35 5.1 General......... 5.2 Design overview.. 35 5.3 Failure modes.. 40 5.4 Design criteria .... 43 5.5 Loadcases 50 6 Materials 55 6.1 Scope. 55 6.2 Materials Unbonded pipe 55 6.3 Materials Bonded pipe.... 60 6.4 Alternative materials.. .64 6.5 Polymerlelastomer test procedures.. 66 6.6 Metallic-material test requirements 69 System design considerations. 72 7.1 72 7.2 General system requirements 72 7.3 Flowline design requirements. 7.4 Riser design requirements 79 7.5 Ancillary components .. .82 7.6 System interfaces ... 86 8 Analysisconsiderations 87 8.1 87 8.2 Analysis techniques 8.3 Loads..... .96 8.4 Global-response evaluation...... 99 9 Prototype testing . 103 9.1 103 9.2 Design programmes 104 9.3 Classification of prototype tests ... 104 9.4 Test requirements... 105 9.5 Test protocol....... 9.6 Procedures Standard prototype tests. 111 9.7 Procedures Special prototype tests.... 116 10 Manufacturing 130 10.1 General.. 130 Copyrght International Organizaionstandardizaonghtsreserved ili se from IHS Not for Resale ISO 13628-11:2007(E) 10.2 Manufacturing . Unbonded pipe ... 10.3 Manufacturing Bonded pipe. .135 10.4 Marking... .137 10.5 Storage.... 140 11 Handling, transportation, and installation. 141 11.1 General..... ..141 11.2 Handling. ..141 11.3 Transportation .143 11.4 Installation .... 144 11.5 Pre-commissioningand commissioning 157 12 Retrieval and reuse. ..161 12.1 General .161 12.2 Retrieval. 161 12.3 Reuse... .163 13 Integrity and condition monitoring .. 13.1 General.. .167 13.2 General philosophy... .167 13.3 Failuremodesandpotentialpipedefects.. 168 13.4 Monitoring methods..... 13.5 Recommendations.. 171 Annex A (normative) Flexible-pipe high-temperature end-fitting qualification test protocol - Volatile-conten