ISO INTERNATIONAL STANDARD 13232-3 Second edition 2005-12-15 Motorcycles Test and analysis procedures for research evaluation of rider crash protective devices fitted to motorcycles - Part 3: Motorcyclist anthropometric impact dummy Motocycles Méthodes d'essai et d'analyse de I'évaluation par la recherche des dispositifs, montes sur les motocycles, visant a la protectiondesmotocyclistes contreles collisions- Partie 3: Mannequin anthropometrique de motocycliste pour essais de choc Reference number ISO 13232-3:2005(E) @ ISO 2005 Copyright International Organization for Standardization Not for Resale ISO13232-3:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyightinteratinal organization for Standardization @ ISO 2005 - All rights reserved nitted without licensefromIHS Not for Resale ISO 13232-3:2005(E) Contents Page Foreword. ..vili Introduction 1 Scope 2 Normative references.. 3 Definitions 4 Mechanical requirements for the motorcyclist anthropometric impact dummy. 4.1 Basis dummy ... 4.2 Motorcyclistdummyheadandheadskins. 4.3 Motorcyclist dummy neck components ...... 4.4 Motorcyclist dummy upper torso components ... 4.5 Motorcyclist dummy lower torso components... 4.6 Arms and modified elbow bushing .... 4.7 Motorcyclist dummy hands.... 4.8 Motorcyclist dummy upper leg components .. 4.9 Motorcyclist dummy frangible knee assembly.... 4.10 Leg retaining cables .... 4.11 Motorcyclist dummy lower leg components. 4.12 Complete motorcyclist dummy ... 4.13 Certification documentation..... 5 Sampling of frangible components . 5.1 Initial conformity of production ... .8 5.2 Subsequentconformityofproduction 5.3 Condition of sampled frangible components .... .8 6 Test methods .... .8 6.1 Frangible bone static bending deflection test .8 6.2 Frangible bone static torsional deflection tes... .9 6.3 Frangible bone dynamic bending fracture test 6.4 Frangible bone dynamic torsional fracture test . .9 6.5 Frangible femur bone static axial load fracture test .... 6.6 Frangible knee static strength and deflection test ... .10 6.7 10 6.8 Motorcyclistneckdynamictestforinitialconformityofproduction.. ..10 6.9 Motorcyclist neck static tests for subsequent conformity of production .... 7 Marking and documentation of frangible components.. 7.1 Marking ... 20 7.2 Documentation.... .20 Annex A (normative) Drawings for motorcyclist anthropometric impact dummy special components .....21 Annex B (informative) Rationale for ISO 13232.-3.... Annex C (normative) Motorcyclist neck subsequent conformity of production test procedures.. 81 ii Copyright Internati uced by IHS unde ense wit t license from IHS Not for Resale ISO 13232-3:2005(E) Figures Figure 1 Extension moment vs. head angle .12 Figure 2 Neck flexion bending moment vs. head angle Figure 3 - Neck flexion occipital condyle and head centre of gravity position . ..15 Figure 4 Flexion neck angle vs. head angle .16 Figure 5 Lateral hea