ISO INTERNATIONAL STANDARD 10750 First edition 2015-06-15 Footwear Test method for slide fasteners Attachment strength of end stops Chaussures-Methoded'essaipourles fermetures aglissiere- Résistanced'attachementdesextrémités Reference number IS010750:2015(E) ISO @ ISO 2015 IS0 10750:2015(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISo at the address below or ISo's member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8. CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org i @ IS0 2015 - All rights reserved IS0 10750:2015(E) Contents Page Foreword ..iv 1 Scope ..1 2 Normative references. 3 Terms and definitions .3 4 Principle. 4.1 General. .3 4.2 Method 1Top stop attachment strength 4.3 Method 2-Bottom stop attachment strength (Slider-stringer method) .3 4.4 Method 3Bottom stopattachment strength (Stringer-stringer method) .3 Apparatus and materials. 6 Test specimens. ..5 7 Procedure ..5 7.1 Method 1—Top stopattachment strength. .5 7.2 Method 2Bottom stop attachment strength (Stringer-slider method) 7.3 Method3-Bottom stop attachment strength (Stringer-stringer method) .6 8 Test report .7 ..8 Bibliography @IS0 2015 -All rights reserved ili IS0 10750:2015(E) Foreword Iso (the International Organizationfor Standardization) is a worldwidefederation ofnational standards bodies (iso member bodies).The work of preparing International Standards is normally carried out throughIsOtechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with Iso, also take part in the work ISo collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISo/IEc Directives, Part 1. In particular the different approval criteria needed for the differenttypes of Iso documents should benoted.This document was drafted in accordance with the editorialrules of theIso/IEC Directives, Part2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this documentmay be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. Details of anypatentrights identified during thedevelopmentof thedocument will be in the Introduction and/or on the Iso list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of Iso specific terms and expressions related to conformity assessment,as wellasinformationaboutISO'sadherencetotheWTOprinciplesintheTechnical Barriers to Trade (TBT) see the following URL: Foreword -Supplementary information Thecommitteeresponsibleforthisdocument isISo/TC216,Footwear. iv @ IS0 2015 - All rights reserved IS0 10750:2015(E) INTERNATIONALSTANDARD Footwear Test method for slide fasteners Attachment strength of end stops 1 Scope This International Standard describes a method intended to determine the attachment strength ofthe top 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.For dated references, only the edition cited applies.For undated references,the latestedition of thereferenced document (includinganyamendments)applies.