ISO/TS TECHNICAL SPECIFICATION 13399-310 First edition 2017-02 Cutting tool data representation and exchange - Part 310: Creation and exchange of 3D models - Turning tools with carbide tips Repreésentation et échange des donnés relative aux outils coupants Partie 310:Création et échange de modeles 3D-Outils de tour a plaquettes en carbures métalliques Reference number ISO/TS 13399-310:2017(E) [so International Organization for Standardization @ IS0 2017 ed without license from IHS IS0/TS13399-310:2017(E) COPYRIGHTPROTECTEDDOCUMENT IS0 2017,Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. IsOcopyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +4122 749 09 47 [email protected] www.iso.org ensee-ZHEJIANG INSTOF STANDARDIzARoISQa7 - All rights reserved Not for Resale, 2017/5/11 02:27:57 etivorking permitted without license from IHS IS0/TS 13399-310:2017(E) Contents Page Foreword ..V Introduction. ...vi 1 Scope. 2 Normative references ...1. 3 Terms and definitions 4 Starting elements, coordinate systems, planes ..2 4.1 General. .2 4.2 Reference system (PCS primary coordinate system) .2 4.3 Tool item position. ..3 4.3.1 General. 4.3.2 Prismatic tool position .3 4.3.3 Round tool position ..3 4.4 Planes 4 4.5 Cutting reference point .5 4.6 Design of the pocket of the tip .6 4.6.1 General. .6 4.6.2 Design of the body of the tip. .6 4.7 Adjustment coordinate system on workpiece side 9 4.7.1 General 4.7.2 Designation of the coordinate system workpiece side .9 5 Design of the model. ..11 5.1 General. .11 5.2 Necessary parameters for the connection interface feature ..12 6 Turning tool No. 1 - Straight design ..12 6.1 General .12 6.2 Necessary properties. ..12 6.3 Basic geometry. ..13 6.4 Turning tool No. 1 - Solid body ..14 7 Turning tool No. 2 - Bent design .14 7.1 General ..14 7.2 Necessary properties ..14 7.3 Basic geometry. .14 7.4 Turning tool No. 2 - Solid body .15 8 Turning tool No. 3 and 6 - Offset side cutting design .15 8.1 General. .15 8.2 Necessary properties. .16 8.3 Basic geometry .17 8.4 Turning tool No. 3 and 6 Solid body ..17 9 Turning tool No. 4 - - Straight grooving design .17 9.1 General. .17 9.2 Necessary properties. 18 9.3 Basic geometry .18 9.4 Turning tool No. 4 solid body .19 10 Turning tool No. 5 - Offset end cutting design .19 10.1 General. .19 10.2 Necessary properties .20 10.3 Basic geometry .20 10.4 Turning tool No. 5 - Solid body 20 11 Turning tool No. 7 - Grooving and cut-off design ..21 11.1 General .21 iii ISee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 ed without license from IHS