TECHNICAL ISO/TS SPECIFICATION 13399-307 First edition 2016-02-15 Cutting tool data representation and exchange - Part 307: Creation and exchange of 3D models - End mills for indexable inserts Representation et échange des données relatives aux outils coupants - Partie 307: Création et échange des modeles 3D -Fraises a plaquettes amovibles Reference number IS0/TS13399-307:2016(E) ISO International Organization for Standardization @ IS0 2016 HEJIANG INST OF STANDARDIZATION C1 5956617 IS0/TS 13399-307:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS02016,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. IsOcopyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Intenationaibr PrganizationforStandardization ensee-ZHEJIANG INST OF STANDARDIZRoISQ ,6 - All rights reserved etworking permitted without license from IHS IS0/TS 13399-307:2016(E) Contents Page Foreword ..vi Introduction. ..vili 1 Scope. ..1 2 Normativereferences 3 Starting elements, coordinate systems, planes ..2 3.1 General. .2 3.2 Referencesystem .2 3.3 Coordinate system at the cutting part. .3 3.4 Planes ..4 3.5 Design of the pocket seat and cutting reference point (CRP) of the insert 5 3.6 Adjustment coordinate system on workpiece side ..8 3.6.1 General .8 3.6.2 Designation of the coordinate system workpiece side ..8 4 Design of the model .9 4.1 General .9 4.2 Necessary parameters for the connection interface feature. .9 4.3 Necessary properties for inserts. .10 4.3.1 General. ..10 4.3.2 Properties for equilateral, equiangular and equilateral, non- equiangular inserts.. ..10 4.3.3 Properties for non-equilateral, equiangular and non-equilateral, non- equiangular inserts. ..11 4.3.4 Design ofthe pocket seat feature ..11 5 End mill, non-centre cutting, single row ..11 5.1 General ..11 5.2 Necessary properties. ..12 5.3 Basic geometry .13 5.4 Determination of the position of the mounting coordinate system of insert .13 5.5 Chip flute and pocket seat .14 5.6 Assembly of a single row, non-centre cutting end mill ..15 6 Single row, non-centre cutting V-groove end mill ..16 6.1 General. .16 6.2 Necessary properties. .17 6.3 Basic geometry. 17 6.4 Determination of the position of the mounting coordinate system of insert .17 6.5 Chip flute and pocket seat .18 6.6 Single row, non-centre cutting V-groove end mill assembly ..19 7 Single row, non-centre-cutting dovetail end mill. .20 7.1 General. 20 7.2 Necessary properties 20 7.3 Basic geometry 21 7.4 Determination of the position of the mounting coordinate system of insert 21 7.5 Chip flute and pocket seat 21 7.6 Single row, non-centre-cutting dovetail end mill assembly .22 8 T-slot end mill. .22 8.1 General 22 8.2 Necessary properties. 23 8.3 Basic geometry .23 8.4 Determination of the position of the mounting coordinate system of insert 23 8.5 Chip flute and pocket seat .24 8.6 Assembly of a T-slot end mill 25 iii e=ZHEJIANG INST OF STANDARDIZATION C1 5956617 thout license from IHS