BS ISO 13992:2014 BSI Standards Publication Alpine touring ski-bindings - Requirements and test methods bsi. ..making excellence a habit. BSISO13992:2014 BRITISHSTANDARD National foreword This British Standard is the UK implementation ofISO 13992:2014. The UK participation in its preparation was entrusted to Technical Committee SW/136/7, Snowsports equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN9780580821066 ICS 97.220.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 October 2014. Amendments issued since publication Date Text affected BSISO13992:2014 ISO INTERNATIONAL STANDARD 13992 Third edition 2014-10-15 Alpine touring ski-bindings Requirements and test methods Fixationspourleskialpinderandonnee-Exigencesetmethodesd'essai Reference number ISO 13992:2014(E) [so @IS02014 BSISO13992:2014 IS0 13992:2014(E) COPYRIGHTPROTECTEDDOCUMENT IS02014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ IS0 2014 - All rights reserved BSISO13992:2014 IS013992:2014(E) Contents Page Foreword. .iv 1 Scope. ..1 2 Normative references. ..1 3 Terms and Definitions ..1 .4 4 Test conditions 4.1 Loading rate 4.2 Accuracyofmeasurement 4.3 Test sole. 4.4 Test ski. .5 5 Test methods A and B .5 5.1 Principle .5 5.2 Simple torsion test. .6 5.3 Forward bending test. 7 6 Requirements and testing. .8 6.1 General requirements .8 6.2 Release testsSetting, reproducibility, and symmetry of release values 9 6.3 Evaluation of reproducibility ofreleaseunder different influences. .11 6.4 Energyabsorption (recentering) .16 6.5 Lateral release under impactloading .17 6.6 .17 Field tests.. 6.7 Exposure to corrosion and dirt. Marking 7 .19 Annex A (informative) Additional information to conduct tests according to test method A ..21 AnnexB (informative)Fixtures and load configurationsnecessaryfor conductingtests using test method B .26 AnnexC (normative) Grain size distribution of dirt ..33 AnnexD (informative)Determination oftolerances onMzand My .34 Bibliography. .36 ISo ISO pub-date year - All rights reserved iii BSISO13992:2014 IS0 13992:2014(E) Foreword Iso (theInternational Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through Iso technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,governmental and non-governmental, in liaison with Iso, also takepart in the work. ISo collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnicalstandardization. The procedures used to developthis document and those intended for its further maintenance are described in the ISO/lEC Directives, Part 1. In particular the different approval criteria needed for the differenttypes of Iso documents should be noted.This document was drafted inaccordance with the editorial rules of the ISo/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn tothepossibilitythat some ofthe elements of this document maybe the subject of patent rights. IsO shal