ISO NTERNATIONAL STANDARD 12573 First edition 2010-09-15 Aircraft Tubing tolerances Inch series Aéronefs - Tolérances de tuyauterie - Série en inches Reference number ISO 12573:2010(E) @ISO2010 E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I4:226"Ocftkf.'Urckp"*cm'tkijv "tgugtxgf+"Ygf"Hgd36*24<58<3;"WVE*4246 ISO 12573:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHTPROTECTEDDOCUMENT ?ISO2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel.+ 4122 749 0111 Fax + 41 22 749 09 47 E-mail copyright@iso.org Web www.iso.org Published in Switzerland ii Iso2010-All rights reserved E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I4:226"Ocftf.'Urckp"cm'tkijvu'tgugtxgf+"Ygf"Hgd’36"24583;"WVE"4246 knnitrawintiInfi ISO 12573:2010(E) Contents Page Foreword iv Introduction. 1 Scope. 2 Normative references. 3 Terms and definitions . 4 Tubes in titanium and titanium alloys .. 4.1 4.2 Tolerances.. 5 Tubes in aluminium alloys. 5.1 Dimensions ... 5.2 Tolerances..... 6 Tubesincorrosionresistantsteel(CRES) 6.1 Dimensions....... 6.2 Tolerances.. 7 Tubes in nickel alloys .. 7.1 Dimensions 7.2 Tolerances ii ruvinti1nft

.pdf文档 ISO 12573 2010 Aircraft — Tubing tolerances — Inch series

文档预览
中文文档 18 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共18页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO 12573 2010 Aircraft — Tubing tolerances — Inch series 第 1 页 ISO 12573 2010 Aircraft — Tubing tolerances — Inch series 第 2 页 ISO 12573 2010 Aircraft — Tubing tolerances — Inch series 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-31 10:20:42上传分享
友情链接
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。