ISO INTERNATIONAL STANDARD 11979-3 Third edition 2012-12-01 Ophthalmic implants Intraocular lenses - Part 3: Mechanical properties and test methods Implants ophtalmiques - Lentilles intraoculaires - Partie 3: Propriétés mécaniques et meéthodes d'essai Reference number IS0 11979-3:2012(E) LSO IS02012 ed without license from IHS Not for Resale IS0 11979-3:2012(E) COPYRIGHTPROTECTEDDOCUMENT ISO2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the addressbeloworIso'smemberbodyinthecountryoftherequester. ISO copyright office Case postale 56:CH-1211 Geneva 20 Tel.+41227490111 Fax +41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ IS0 2012 - All rights reserved No reproductic networking permited without license from IHS Not for Resale IS0 11979-3:2012(E) Contents Page Foreword ..iv Introduction. ..V 1 Scope. ..1 2 Normative references ..1 3 Terms and definitions ..1 4 Requirements .1 4.1 General .1 4.2 Tolerances and dimensions. .2 4.3 Clearance analysis (anterior chamber lenses only) 2 4.4 Compression force 2 4.5 Axial displacement in compression 2 4.6 Opticdecentration .3 4.7 Optictilt. .3 4.8 Angle of contact ..3 4.9 Compression force decay .3 4.10 Dynamic fatigue durability .3 4.11 Surgical manipulation. .4 4.12 Surface and bulk homogeneity .4 5 Recovery of properties following simulated surgical manipulation ..4 6 Additions for accommodating IOLs (AIOLs) ..4 Annex A (normative) Measurement of compression force ..6 Annex B (normative) Measurement of axial displacement in compression ...9 Annex C (normative) Measurement of optic decentration ..12 Annex D (normative) Measurement of optic tilt ..15 Annex E (normative) Measurement of angle of contact ..19 Annex F (normative) Testing of compression force decay ..22 Annex G (normative) Testing of dynamic fatigue durability ..23 Annex H (informative) Measurement of loop pull strength ..25 Annex I (informative) Clearance analysis.. ..27 Annex J (informative) Precision ..30 Bibliography .31 iii se with IS thout license from IHS Not for Resale

.pdf文档 ISO 11979-3 2012 Ophthalmic implants — Intraocular lenses — Part 3 Mechanical properties and test methods

文档预览
中文文档 39 页 50 下载 1000 浏览 0 评论 309 收藏 3.0分
温馨提示:本文档共39页,可预览 3 页,如浏览全部内容或当前文档出现乱码,可开通会员下载原始文档
ISO 11979-3 2012 Ophthalmic implants — Intraocular lenses — Part 3  Mechanical properties and test methods 第 1 页 ISO 11979-3 2012 Ophthalmic implants — Intraocular lenses — Part 3  Mechanical properties and test methods 第 2 页 ISO 11979-3 2012 Ophthalmic implants — Intraocular lenses — Part 3  Mechanical properties and test methods 第 3 页
下载文档到电脑,方便使用
本文档由 人生无常 于 2024-08-31 10:05:01上传分享
加微信群 有优惠
站内资源均来自网友分享或网络收集整理,若无意中侵犯到您的权利,敬请联系我们微信(点击查看客服),我们将及时删除相关资源。